Get a Quote

What is an R-value?

What is an R-value? With greater emphasis being placed on the U-value of new builds as regulations tighten we take a look at what factors are involved in reaching the magical low figures designed to get building control officers’ hearts racing! We’ve already written about U-values, the measure of the rate of heat flow through a wall, floor or roof – but how exactly is a U-value calculated? We asked architect Thomas Wiedmer, who is technical manager at insulation specialist Actis, to explain. "The fabric of a building is a crucial factor in determining its overall energy efficiency. The new target Fabric Energy Efficiency rate stipulates that the physical envelope of the house - the longest lasting element of every new home – plays the greatest part in ensuring this efficiency.

The target FEE stresses that greater emphasis must be placed on the U-value of a new build – the lower the figure the more efficient the envelope. U-values are expressed as W/m2K – the rate in watts at which heat transfers through a square metre of the surface of an element when there is a temperature difference of one Kelvin between the inside and outside of the element (that is, a wall, floor or roof). A U-value doesn’t apply to any individual material used in the build up, but to each of these elements as a whole. So a brick won’t have a U-value, but a build up consisting of brick, block, mortar, insulation and so forth does have a U-value.

What each material component does have though is an R-value – or thermal resistance, which is the resistance to the transfer of heat across the material. While U-values need to be as low as possible for maximum efficiency, R-values have to be as high as possible. Think of water attempting to get out of narrow tap compared with it just cascading over the edge of a weir. T

he latter is a much easier route and the number of gallons per minute achievable is far higher in the latter scenario – the aperture of the tap gives far greater resistance than the edge of the weir. R-values are shown as m2K/W. In order to determine the R-value of each fabric we need to determine the thermal conductivity of each of the materials used in the build up – the lambda value.

Many materials have a standardised lambda value. A sort of construction equivalent of a periodic table exists defining the thermal conductivity of each material – how much heat is conducted through a cubic metre of material with a one Kelvin temperature difference between side A and side B.

In this case the volume and thickness of the material is irrelevant. The more easily a material conducts the higher its lambda value. As an example aluminium, which conducts heat very easily, has a lambda value of 160 W/mK, steel – 50 W/mK and brick 0.72 W/mK. The thermal resistance is then calculated by dividing the thickness of a material (in metres) by its thermal conductivity (lambda value - ?).

For non-standard products verified lab tests are carried out to test the lambda or R-values enabling specifiers to declare values (?D or RD) which can be included among their calculations. The overall R-value of a multi-layered element can be calculated by adding the R-values of its component materials. U-values are often described as being the reciprocal of the sum of R-values of an element. However, the inside and outside surface thermal resistances (Rsi and Rse) needs to be added. So when determining U-values one needs to follow the following steps: actis R value graphic 1. note lambda value and thickness of each individual material 2. work out R-value of each element by dividing the thickness by the Lambda value 3. add up all the R-values and apply bridging factors 4. include the R-values of both internal and external surface thermal resistance 5. divide one by the total R-value to get the U-value A simple formula to illustrate this is R = T/C C = T/R T = R x C Thermal conductivity or lambda value refers to the material only, making no allowance the thickness. Thermal resistance or R-value is the thickness of the material in metres divided by the lambda value. And thermal transmittance or U-value is one divided by the total R-value of all layers in the element build up plus the internal and external surface thermal resistances.”

ACTIS logo white on grey with outline 0309

By Thomas Wiedmer, Technical Manager at Actis insulation.



Thomas Wiedmer- Guest Blog

Author: Thomas Wiedmer- Guest Blog

This article was published by Thomas Wiedmer- Guest Blog on 22.04.2015.